Concrete Testing Equipment

Product Details:

About Product :
We are providing an extensive series of Hand OperatedCompression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of Hand OperatedCompression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Delivery Time: 1 Week

Product Details:

About Product :

The Narrow Gap J-Ring test is used for determining the passing ability, the flow spread and the flow time of self compacting concrete as the concrete flows through the JRing apparatus.


Specifications :

• The J-Ring narrow gap with ø18 mm x 16 smooth bars is manufactured from stainless steel.
• The Slump Cone is made from sheet steel protected against corrosion, with diameters; top 100 mm, base 200 mm and with a height of 300 mm.
• The Base plate is 900x900x3 mm square, made of stainless steel with engraved circles of 200 mm and 500 mm diameter conforming to EN 123508.
• The Steel weighted collar is used to stabilize the slump cone on J-Ring or slump flow tests.
• Minimum apparatus for the J-Ring test are J-Ring with narrow gap and slump cone.

Additional Information :

• VSLIC 2009 J-Ring, narrow gap
• VSLIC 2002 Slump cone for J-Ring
• VSLIC 2009-A Base plate for J-Ring and slump-flow tests
• VSLIC 2009-B Steel weighted collar, 9 kg
• VSLIC 2009-C EN 12350-8 for slump cone on J-Ring or slump flow test
• Item Code: VSLIC-2009
• Minimum Order Quantity: 01 Piece

Additional Information:

• Item Code: VSLIC2009
• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of Digital Compression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Item Code: VSLIC2055-B
• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of Hand Operated Compression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of Analog Compression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Delivery Time: 1 Week

Product Details:

The quality of concrete is mainly judged by its compressive strength directly affecting the load-bearing capacity and durability of concrete structures. Proceq invented the Original Schmidt Hammer, the world’s first and now most widely used test hammer for analyzing the compressive strength of concrete properties.

The Original Schmidt hammer will hit the concrete at a defined energy whereas its rebound is dependent on the hardness of the concrete and is measured by the instrument. The Original Schmidt hammer is available in models with different impact energies.Each test hammer designed for a specific test application, in order to meet the needs of the customers to investigate a wide range of material types and sizes, such as bridge decks, thin walls, cast stone components or small components.

Additional Information:

• Item Code: VSLIC-2068
• Delivery Time: 1 Week

Product Details:

About Product :
This Cube Mould (Three Gang) forms three cubes at one time in a diagonal arrangement. Mould and detachable base are held together by self-aligning thumbscrews, which ensure an even, tight fit.

Specifications :

• Dimension : 50mm x 50mm x 50mm

• Type : Die casting Moulds

• Weight approx.: 6 kg

Additional Information :

• Product Code : VSLIC-2034

Additional Information:

• Item Code: VSLIC-2034
• Delivery Time: 1 Week

Product Details:

Digital Compression Testing Machine has been designed to meet the need for a simple, economic and reliable means to test concrete for its compressive strength. The design expressive of simplicity, both of construction and operation, makes the machine easy to use and maintain. The unit is compact, making it useful for site and Laboratory applications. The digital machines are provided with a pace rate controller, to enable maintain a constant of loading.

Features :

• High stability four column load frame
• Each frame tested for stability and alignment to avoid tension failure during a test and to ensure center loading
• Standard Platens for 3 X 6”/ 4 X 8” and 6 X 12” cylinders included.
• A precise large diameter spherical upper platen for optimum results
• Variety of optional accessories for cubes, blocks, bricks and flexure test available
• Motorized hydraulic power pack or pumping unit with rapid approach and automatic over load protection
• Comes standard with safety Guards on all four sides.

Product Details:

About Product:
Vertex Instrument is manufacturing Cube Moulds as per international standards (BS and IS). These cube moulds are available in different sizes. For the metric size cube mould, the faces are machined flat to +/-0.2mm accuracy and finished to within 0.2mm. For the inch size moulds, the faces are machined flat to +/-0.01 inched to within 0.01in. All cube moulds are supplied complete with the base plate.

Specifications: 

• Material : Cast iron

• Mould Size : 50mm
• Mould Shape : Square

Additional Information :

• VSLIC2024A Cast Iron Mortar Cube Mould 50mm, Single Gang
• VSLIC2024B Cast Iron Mortar Cube Mould 50mm, Three Gang
• VSLIC2024C Mild Steel Cement Cube Mould 70.6mm, with Loose Base Plate
• VSLIC2024D Cast Iron Concrete Mould 75mm Single Gang
• VSLIC2024E Cast Iron Concrete Mould 100mm Light Weight
• VSLIC2024F Cast Iron Concrete Mould 100mm Clamp Type (8.5 KG) Four Part
• VSLIC2024G Cast Iron Concrete Mould 150mm Light Weight 8KG
• VSLIC2024H Cast Iron Concrete Mould 150mm ISI Marked
• VSLIC2024I Cast Iron Concrete Mould 150mm Clamp Type (18 KG) Four Part
• VSLIC2024J Cast Iron Concrete Mould 150mm Clamp Type (16 KG) Two Part

Additional Information:

• Item Code: VSLIC-2024
• Delivery Time: 1 Week

Product Details:

About Product :
The V Funnel apparatus is used to evaluate the flow time of freshly mixed self compacting concrete. The test is not suitable when the maximum size of the aggregate exceeds 22.4 mm. The test set consists of a stainless steel funnel placed vertically on a supporting stand. The discharge orifice is equipped with a lid, which can be momentarily opened.

The l shape box apparatus is supplied complete with:

• Filling Hopper
• Base

Features

• Overall dimensions: 570x300x920 (h) mm

Additional Information:

• Item Code : VSLIC2011

 

Minimum Order Quantity: 01 EACH

Additional Information:

• Item Code: VSLIC2011
• Delivery Time: 1 Week

Product Details:

About Product :
We are the manufacturer of Initial Surface Absorption Test (ISAT) Apparatus. This apparatus is used to assess the surface absorption characteristics of concrete.The rate of flow of water per unit area into a concrete surface when subjected to a constant head of 200 mm is measured. The unit consists of a capillary tube mounted on a scale, a water reservoir & connecting tubes. Easy to use, mounted on a stand. 

Specifications :

• Brand : vertex 
• Size : 200 mm
• Material : Stainless Steel, Plastic
• Accuracy : +/- 1
• Minimum Oder : 01

Additional Information :

• Item Code :  VSLIC2008
• Standards :  BS1881 PART 208

Additional Information:

• Item Code: VSLIC2008
• Delivery Time: 1 Week

Product Details:

The U Shape box apparatus is used to determine the filling and passing ability of self-compacting concrete (SCC). The U box is made of stainless steel consisting of three 12 mm dia. Rebars. The U box is mounted on a frame with a fixing mechanism
Additional Information:

Minimum Order Quantity: 01 EACH

Product Code: VSLIC 2013

Product Details:

About Product :
Keeping our synchronization with the development taking place in this industry, we are engrossed in delivering a broad range of Concrete Curing Racks.These durable racks are manufactured from plastic compounds and recycled materials to resist moisture, abrasion, chemical and temperature variations. Each rack has built-in handles, making them easy to carry and safely stacked 12 tiers (58") high. The racks unique open frame design allows water vapor to flow through and saturate the surface of each individual cylinder, and also separates and prevents cylinder surfaces from touching each other for improved temperature control. 

Each rack holds 4 pieces 100 x 200 mm cylinders and is 17-5/8" wide x 6-3/8" deep. The weight of one rack with 4 cylinders is approximately 17 KG.One base rack is required for each stack.

Features:

• High quality
• Seamless finish
• Durable

Additional Information:

• Item Code: VSLIC2035
• Delivery Time: 1 Week

Product Details:

About Product :

K-Slump Tester for in-place measurements indicates correlation to the slump test. The probe determines workability of concrete and the degree of compaction. Includes correlation chart and instructions.

Specifications :

• Total length: 400 mm
• Weight approx.: 2 kg

Additional Information:

• Item Code: VSLIC2004
• Delivery Time: 1 Week

Product Details:

About Product :
Our company specializes in manufacturing, supplying and exporting Buoyancy Balance. Our offered balance is extensively used for weighing applications. This balance is highly acknowledged for sturdy construction, high strength and accurate results. High-quality raw materials are used to manufacture this balance in accordance with the international quality standards. Post-production, this balance is stringently checked on various parameters to ensure zero-defect. Buoyancy Balance is available in various specifications as per the variegated requirement of clients.

Features:

• Adjustable water tank for raising or lowering
• In-built anti-interference shield
• A wide and bright LCD screen display
• Reliable and stable results
• Standard interface output with unit conversion
• Easy to operate and maintain
• Separate button for compensating zero error
• Ideal for precise as well as general weighing applications

Technical Specifications :

• Power Supply: 110-240V AC,50-60Hz,1Ph
• EN 12697-32: Yes
• EN 13280-4: Yes
• BS 598-104: Yes

Additional Information:

• Item Code: VSLIC-2053
• Delivery Time: 1 Week

Product Details:

Vertex Instrument is manufacturing plastic Cube Moulds as per international standards (BS and IS). These cube moulds are available in different sizes. For the metric size cube mould, the faces are machined flat to +/-0.2mm accuracy and finished to within 0.2mm. For the inch size moulds, the faces are machined flat to +/-0.01 inched to within 0.01in. All cube moulds are supplied complete with the base plate.

Specifications:

• 50 mm cubes strips.
• Set comes complete with tamper and mold top.
• Offers substantial cost savings.
• High-density polyethylene.

Additional Information:

• Item Code: VSLIC-2033
• Delivery Time: 1 Week

Product Details:

About Product :
This apparatus is used to assess the surface absorption characteristics of concrete.The rate of flow of water per unit area into a concrete surface when subjected to a constant head of 200mm is measured.

The unit consists of a capillary tube mounted on a scale, a water reservoir connecting tubes. Easy to use, mounted on a stand.

Additional Information:

• Item Code: VSLIC-2008
• Minimum Order Quantity: 1 Piece

Additional Information:

• Item Code: VSLIC-2008
• Delivery Time: 1 Week

Product Details:

Specification:

The Concrete mixer has been designed for mixing small quantities of concrete used in the preparation of concrete cubes, for testing in laboratories. The purpose of the mixer is to smear mechanically the aggregate surface with cement paste uniformly & produce a mix of uniform consistency. This, in turn, gives a consistent quality of cubes specimens when casting in the moulds. The Concrete Mixer developed is transportable on wheels. The design of mixing paddles ensure uniform & efficient mixing of cement & aggregate both in dry & wet conditions. This machine is suitable for an aggregate size of up to 20 mm. The equipment can also be put to use for mixing any other material in dry/wet
conditions. The arrangement helps the operators to access the pan contents conveniently & emptying the mixture after completion of the operation. The drum is driven off the ribbed base. The lid with mixing paddles clears off the
top of the drum to provide maximum access to the operator.

 

Specifications :

Mixing Capacity: 40 ltrs.
Overall Dimension : 910 x 875 x 1250 mm
Motor : 2 HP, 960 RPM
Power supply : 440 V, 50 Hz, 3 phase AC

Features:

•  Portable, compact & easy to operate
•  Adjustable blades
•  Simple to clean & maintain

Product Details:

About Product :
It is designed to carry a load of 140 kg. The apparatus consists of a motor fitted with a variable pitch pulley housed in a cabinet. The vibrations are imparted by means off-balance masses rotating on a shaft of a vibrator clamped to the underside of the table top. The table top is 500 x 500 mm and has stops along its edges to prevent moulds from walking off the table during vibration. A crass arm adjustable on a vertical rod at the centre of the table is provided to hold the moulds while operating the between a maximum of 3600 vibrations down to 2600 vibration per minute. A speed regulation handle is provided for increasing or decreasing frequency. A switch is provided for starting the motor. Suitable for an operator on 230 Volts, A.C. Single Phase, 50 Cycles.
Note: Tabletop size : 750 x 750 mm & 1000 x 1000 mm alsoavailable at an extra cost. Both models operate on 440 volts, A.C. Three Phase

Additional Information:

• Item Code: VSLIC-2047
• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of Analog Compression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of Digital Compression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Item Code: VSLIC2055-A
• Delivery Time: 1 Week

Product Details:

About Product :
The compaction factor is defined as the ratio of the mass of the concrete compacted in the compaction factor apparatus to the mass of the fully compacted concrete. It involves dropping a volume of concrete from one hopper to another and measuring the volume of concrete in the final hopper to that of a fully compacted volume. The results of the compaction factor test can be correlated to slump, although the relationship is not linear. This test is difficult to run in the field and is not practical for large aggregates (over 1 inch) Compared to the slump test, the apparatus is bulky and a balance is required to perform measurements.

Product Specifications :
The apparatus, consisting of a rigid frame that supports two conical hoppers vertically aligned above each other and mounted above a cylinder. The top hopper is slightly larger than the bottom hopper, while the cylinder is smaller in volume than both hoppers. To perform the test, the top hopper is filled with concrete but not compacted. The door on the bottom of the top hopper is opened and the concrete is allowed to drop into the lower hopper. Once all of the concrete has fallen from the top hopper, the door on the lower hopper is opened to allow the concrete to fall to the bottom cylinder. The excess concrete is carefully struck off the top of the cylinder and the mass of the concrete in the cylinder is recorded. This mass is compared to the mass of fully compacted concrete in the same cylinder achieved with hand rodding or vibration. Complete with the trowel and tamping bar 0-60 cms long X 16mm Dia.

Additional Information :

Dimensions: 500x400x1510 mm

Weight: 55 kg approx.

Standards: ASTM C 403, AASHTO T197

Additional Information:

• Item Code: VSLIC-2007
• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of AnalogCompression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Delivery Time: 1 Week

Product Details:

About Product :
We are providing an extensive series of Digital Compression Testing Machine, which are available in varied specifications that meet on client’s demand.

Features:

• High stability.
• Self-aligning platen assembly.
• Load Gauges are calibrated in kN against certified Proving Rings, traceable to NPL / NCCBM.
• Suitable for testing cubes and cylinders of various sizes.
• Using special platens, bricks can also be tested.
• Logged data printing facility through a parallel port interface available in digital and microcontroller based versions.
• Calibration process accredited by NABL (National Accreditation Board for Laboratories).
• Machines with CE mark also available, on special request.
• Operator’s safety features like a metal door with a perspex window and overload tripping device are provided in all models.
• Longevity
• Industry proven designs

Other Information :

• Application: Compressive Strength Measurement

Additional Information:

• Item Code: VSLIC2055-C
• Delivery Time: 1 Week

Product Details:

About Product :
It is used for finding out the rate of hardening of mortar sieved
from concrete spring and a stem graduated from 0-70 kg x 1 kg.
Six interchangeable penetration needles of areas 645, 323, 65
32 and 16 mm sq. is provided . The penetration resistance is measured by the force exerted to penetrate the mortar by 25 mm and is indicated by a sliding ring on the stem, which is
graduated. Needle shanks are marked at every 12.5 mm. Supplied complete in a wooden carrying case.

Specifications :

• Areas of Needle : 645, 323, 65 32 and 16 mm sq.
• Material : Stainless Steel
• Color : Silver
• Stem Graduated From : 0-70 kg x 1 kg
• Minimum Quantity : 01

Additional Information :

• Item Code : VSLIC2015
• Standards : ASTM C-403

Additional Information:

• Item Code: VSLIC2015
• Delivery Time: 1 Week

Product Details:

About Product:
The apparatus is used to determine the workability of Portland cement concrete. The Kelly ball test is considered to be simple and much faster than the slump test. Twice the Kelly ball reading approximately equals the slump

Specification:

• The apparatus is used to determine the workability of Portland cement concrete.
• The Kelly ball test is considered to be simple and much faster than the slump test.
• Twice the Kelly ball reading approximately equals the slump.
• It consists of a cylinder with a ball-shaped bottom and handle, together weighing 15 kg.
• A strip frame guides the handle and serves as a reference for measuring the depth of penetration.
• The handle is graduated in mm.
• Penetration can be recorded to the nearest 0.5 mm.

Additional Information:

• Minimum Order Quantity: 01 Piece
• Product Code: VSLIC-2006
• Standard: ASTM C-360

Additional Information:

• Item Code: VSLIC-2006
• Delivery Time: 1 Week

Product Details:

Accelerated Curing Tank is generally estimated after 28 days by crushing field test cubes or cylinders made from the representative concrete used for the structure. The utility of ascertaining strength after 28 days is often questioned since by this time considerable concrete would have been placed and work may have progressed. It is then rather too late for remedial measures. It is therefore of tremendous advantage to predict 28 days strength within a few hours of casting the concrete so that, we have a good idea about the strength of the concrete.

Other Details:

The rate of gain of strength of concrete depends on the reaction rate of cement and additions with water (Hydration). In common with all chemical reactions, the rate of reaction depends on reaction of temp. Higher reaction temperature gives higher rate of reaction e.g. the concrete gains strength more rapidly when its temp. is higher. Accelerated curing is the process by which the temperature of the concrete is raised artificially by applying external heat to speed up the rate of gain in strength.

The test method covers procedures for curing test specimens of concrete stored under conditions intended to accelerate the development of strength. The procedures: Procedure A- Warm Water Method, Procedure B-Boiling Water Method.

Specifications:

Accelerated Curing Tank having capacity to accommodate 6/ 12/ 18 Concrete Cubes of 150 mm size with a facility for accelerated curing by Boiling water method up to temperature range: 100 /- 2 deg.C as per IS standard IS : 9013. Also it will have capacity for curing by warm water method at temperature 55 /- 2 deg.C

Tank will consist of a rectangular double-walled metal cabinet, inside lined with stainless steel, outer powder coated. Easily replaceable high Wattage heaters are mounted inside the chamber. A slow speed stirrer is provided to circulate water inside the chamber to maintain the uniform temperature of water. A strong stainless steel perforated platform is provided for keeping the cubes and also have a lid with lifting handle to cover the chamber.

The temperature is indicated and controlled by a Digital Auto-Tuning PID Temp. Controller with soak timer to control the duration of heating and then to shut down the system without manual attendance. The front panel will have power supply indicating lamp, control action indication lamp and one main switch. Suitable for operation on 220 V, 50 Hz single phase, AC supply or 440 V 50 Hz, three phase AC supply, for bigger size of curing tank.

Optional Accessories:

Rubber Hand Gloves.

Spare heaters.

Low water Level cut off device to safeguard heaters against low water level burn out.

In built refrigeration system for curing at 27 deg C

Product Details:

Vertex Series of Compression Testing Machines are the finest of their types available. Their rugged construction and extreme simplicity makes it possible for even non-technical personnel to operate them with ease and complete dependability. In particular, the portable units, which are small in dimensions, sturdy and light in weight, make quality control testing possible in areas where commercial testing facilities are not available and where the transportation of larger and much heavier machines would be difficult. Vertex Compression Testing Machines conform to IS: 14858(2000) and calibrated with an accuracy of± 1 % as per the requirement of 1828(Class1). It can also be supplied as per BS: 1881 and other associated International Standards. These machines are available in 50kN, 100kN,500kN, 1000kN,2000kN, 3000kN & 5000kN Capacities.

Models available:

CTM Analogue- Hand operated (capacity 50kN,100kN,250kN,500kN,1000kN) 

CTM Analogue- Electrically operated (capacity 50kN,100kN,250kN,500kN,1000kN,2000kN &3000kN)

CTM Digital-Electrically operated (capacity 50kN,100kN,250kN,500kN,1000kN,2000kN &3000kN) 

CTM Micro Controller Based (capacity 50kN,100kN,250kN,500kN,1000kN,2000kN,3000kN & 5000kN) 

CTM Digital- (capacity 50kN,100kN,250kN,500kN,1000kN,2000kN & 3000kN) 

Additional Information:

• Item Code: VSLIC2055
• Pay Mode Terms: T/T (Bank Transfer)
• Delivery Time: 4 to 7days
• Packaging Details: Wooden

Product Details:

To furnish the varying desires of our customers, we are immersed in offering a world class consignment of Cylindrical Mould. Vertex manufactures cylindrical moulds of metal for specimen testing and analyses of concrete columns. We make cylindrical moulds in standard sizes that are widely used by the civil engineering labs in India and world for testing the compression, linearity, stability and other essential attributes of concrete columns. The moulds are delivered high-quality finish at its inner surface to ensure that best specimens are derived without any imperfection. Our cylindrical mould is developed with high-grade steel and cast iron material that offer strength and durability, especially the rust and corrosion resistance. The dimensional make of the moulds is such that deformation is negligible even after continued and regular use of them.

Specifications:

• The moulds are split vertically into two parts.
• The mean internal diameter in within +/-0.2mm and height is within +/-1mm.
• The ends are machined to +/-0.05.
• The base plate and top plate are machined flat to +/-0.03mm.

Other Information:

• Customized
• Reliable
• Fine finish
• 150 mm dia x 300 mm high
• VSLIC2025A Mould cylinder, cast iron, 150mm dia x 150mm height.
• VSLIC2025B Mould cylinder, cast iron, 150mm dia x 300mm height.
• VSLIC2025C Mould cylinder, cast iron, 160mm dia x 320mm height.
• VSLIC2025D Mould cylinder, cast iron, 100mm dia x 200mm height.
• VSLIC2025E Mould cylinder, cast iron, 300mm dia x 600mm height.

Additional Information:

• Item Code: VSLIC-2025
• Delivery Time: 1 Week

Product Details:

About Product :

The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees, which is defined as the time in seconds to complete required vibrating at which the fresh concrete flows out sufficiently to come in contract of the entire face of acrylic disc.

Specification:
The equipment consists of : A vibrating table size 380 mm long and 260 mm wide, resting upon elastic support at a height of about 305 mm above the floor, complete with Start/Stop switch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescoped with funnel and guide swivel arm is also detachable from the vibrating table. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16 mm dia and 600 mm long rounded at both ends.

Additional Information:

• Minimum Order Quantity: 01 EACH
• Product Code: VSLIC 2001

Additional Information:

• Item Code: VSLIC2001
• Delivery Time: 1 Week or Depend on the Distance

Product Details:

About Product :
Economical method of quickly estimating the air content of fresh concretein the field using the isopropyl alcohol method. Does not replace conventional air meter method of air content testing.

Specifications :

• Display Type : Analog
• Material : Glass
• Power Source : Electric
• Minimum Order : 01

Additonal Information :

• Item Code :VSLIC2005

Additional Information:

• Item Code: VSLIC2005
• Delivery Time: 1 Week

Product Details:

Supported ourselves with proficient amenities, we are readily instrumental in providing an inclusive variety of Beam Mould. The proposed models range from the traditional steel models conforming to ASTM standards, to the slitting plastic models, very practical for field use and ideal for production control.

 

Features:

• Specifically designed
• Long lasting
• Reliable

Additional Information:

• VSLIC2029A 100 x 100 x 500 mm Polyurethane 2.5 KG
• VSLIC2029B 150 x 150 x 700 mm Polyurethane 4.8 KG
• VSLIC2029C 150 x 150 x 750 mm Polyurethane 5.0 KG
• VSLIC2029D 150 x 150 x 600 mm Polyurethane 4.4 KG

Additional Information:

• Item Code: VSLIC-2029
• Delivery Time: 1 Week

Product Details:

About Product :

Steel beam moulds are manufactured in accordance with dimensions and tolerances stated in the related standards. Two-part and clamp attached base plate steel moulds are designed to be durable, resistant and easy to clean.

Specifications:

There are 2 sets available in this product. One is Set -1120 A. Its beam mould is 100mm X 100mm X 500mm and the other is the Set – 1120 B. Its beam mould is 150mm X 150mm X 700mm. The flatness of the faces is +/- 0.2 mm and it is also finished in 0.2 mm.

Other Details :

• Precised designs
• High quality
• Long lasting
• Beam Mould 150 mm x 150 mm x 700 mm made of Cast Iron
• BS 1881-108 Standard.
• VSLIC 2026A 100 mm x 100 mm x 500 mm
• VSLIC 2026B 150 mm x 150 mm x 700 mm
• VSLIC 2026C 150 mm x 150 mm x 750 mm
• VSLIC 2026D 100 mm x 150 mm x 600 mm
• VSLIC 2026E 150 mm x 150 mm x 600 mm

 

Additional Information:

• Item Code: VSLIC-2026
• Delivery Time: 1 Week

Product Details:

Being the market leader of this domain, we manufacture and export Briquette Mould Three Gang. By using latest machinery and cutting-edge technology, we manufacture the rendered briquette mould three gangs in accordance with the industry laid norms. Used in construction material testing applications, the quality of the rendered briquette mould three gangs is always maintained.

Specifications:

• The standard spatula consists of a steel blade, of a special shape. A wooden handle is fixed to the stem of the blade. The weight does not exceed 340 gms.

Additional Information:

• Optimum functionality
• Easy to use
• Low maintenance
• IS 269 1958, Bs12 Standards
• Item Code: VSLIC-1020

Additional Information:

• Item Code: VSLIC-1020
• Delivery Time: 1 Week

Product Details:

About Product :
For casting of cement briquettes for tensile strength tests. It is a two part split mould made of gun metal. Two thumb screws facilitate easy and quick assembling and dismantling of the mould.

A set of three moulds as per IRC-SP-53-2002 made of brass /gunmetal with the shape, dimensions and tolerances.
The ends B & B` are known as clips, and the parts A & A'' are known as sides of the mould. The dimensions of the mould
shall be such that when properly assembled it will form a briquette specimen having the following dimensions.
Total length : 75 ± 0.5 mm

Specifications :
Brand : Vertex
Material : Gun Metal
Briquttes Cast :  25.4mm x 25.4mm
Application : Tensile Strength Test
Base Plate : Steel
Minimum Quantity : 01

 

Additional Information:

• Item Code: VSLIC4027
• Delivery Time: 1 Week

Product Details:

VS-LBY Concrete Thickness Detector is a portable non-destructive testing instrument for measuring the thickness of concrete or other non-ferromagnetic media. When used, the transmitter and receiver probes are placed on the two relative test surfaces of the Concrete, respectively, transmitting and receiving electromagnetic fields. The instrument transmits and receives electromagnetic fields according to the received signals. Strength, test Concrete thickness.

 

FEATURES:

 ·      Upgraded wireless cloud transmission function.

·      Adopt three anti-shell design, waterproof, dust-proof and shock-proof.

·      Separate design of probe and main engine facilitates on-site measurement and use by operators.

·      Store the measurement results of floor thickness according to components.

·      Simple and easy to use, with perfect measurement, storage and analysis functions

·      Stored data is transmitted to computer through USB interface.

Use Windows software to analyze data and generate test reports.

Additional Information:

• Packaging Details: Material: engineering plastic volume: 420¿¿140¿¿335mm weight: 6.5kg

Product Details:

About Product :
High-precision balances with comprehensive functions to handle diverse applications and increase productivity.

Specifications :
Weight Capacity : 10kg,50kg,100kg,300kg
Minimum Order: 1 Unit
Material Construction: Stainless Steel
Use: Industrial / Home / Office

Additional Information:

• Delivery Time: 1 Week

Product Details:

About Product :
Backed by a rich industrial experience, we are engaged in offering a commendable array of Concrete Flow Table Test Set. The test set is used for concrete mixes of high workability and determines flow index as an arithmetic mean of the diameter of the specimen after working on a flow table. The apparatus consists of a double steel table, an upper table measuring 700 x 700 mm and hinged at one side to the lower table. The top table is inscribed and all parts are protected against corrosion. The stainless steel cone has a 130 ±2 mm top diameter, 200 ±2 mm base diameter and 200 ±2 mm height and 1.5 mm thickness. Dimensions: 700 x 850 x 300 mm, Weight (approx.) 40 kg.
This Equipment is used for concrete mixes of high workability and determines flow index as an arithmetic means of the diameter of the specimen after working on a flow table.
Features:

• Reliable
• Longevity
• Durable
• Robust

Specifications :

• Dimensions: 700 x 850 x 300 mm
•  Weight (approx.) 40 kg
• Shape : Square 
• Operation On : Hand
• Brand : Vertex
• Surface Finish : Painted

Additional Information:

• Item Code: VSLIC2010
• Delivery Time: 1 Week

Product Details:

About Product :
The L-Shape Box is used for determining the passing ability rate of freshly mixed self-compacting concrete. The distance between 12 mm diameter bars can be set between 41±1 mm or 59±1 mm. L-Shape box is designed for ease of cleaning the vertical and horizontal hoppers.

The L shape box apparatus is supplied complete with:

• Filling Hopper
• Base  

 

Specifications:

• Shape : L Shape
• Color : Other Color
• Distance Between : 12 mm diameter bars can be set between 41 +/- 1 mm or 59 +/- 1 mm
• Minimum Order Quantity : 01

Additional Information:

• Item Code: VSLIC2012
• Delivery Time: 1 Week